🖨️ Print Shop
Nissafors Trolley Modular Organizer

IKEA Nissafors Organizer System Boost Me A simple Organizer System created for the IKEA NISSAFORS Rolling Table. It is really easy to print, with no visible layer lines and no supports needed. The Project is set up to fit all bambulab printers including the A1 Mini. For installation, you just need to print the proper modules and place them on the table. You will need at least 2 Corner Modules (P1 & P2) to create a sturdy Organizer Base. It is essential to use the Corner Modules on the corner positions of the table, as they are designed to align with the small screw heads on top of the NISSAFORS surface. This way, the modules stay securely in place without any additional installation. Be sure to take a look at the pictures, as there are a couple of different base module variations. You can find all modules in the print profiles to assemble your personal organizer setup. Below, you can find a guide to each base module: Corner Module v1 P1: Base Module for the Corner Position featuring 4 Slots for Containers. Corner Module v1 P2: Mirrored Version of Corner Module v1 P1 for the Corner on the other side. Corner Module v2 P1: Base Module for the Corner Position featuring 3 Slots for Containers (2x Rectangular, 1x Wide). Corner Module v2 P2: Mirrored Version of Corner Module v2 P1 for the Corner on the other side. Middle Module v1: Base Module for the Middle Position featuring 4 Slots for Containers. (can be used on both sides) Middle Module v2: Base Module for the Middle Position featuring 3 Slots for Containers. (can be used on both sides) You can find all modules in the print profiles to assemble your personal organizer setup. I also created a small connector piece that interlocks all base modules with each other. You can find it in the print profiles under “ Connector Piece ”. The Containers After you have succesfully printed a base grid, you can select and print the containers. There are two different sizes: Basic Container: 71 × 77 × 100 mm Wide Container: 71 × 155 × 100 mm In the pictures, you can find a selection of all available container variations. Membership

Nissafors Trolley Modular Organizer

by neilvfx · original on MakerWorld ↗

♥ 101⬇ 19🖨 11 prints

License: Standard Digital File LicenseIKEAnissaforsNissaforstableorganizermodularcontainerstorageofficesystem

Print profiles

  • Corner Module v1 P1

    ⏱ 2h 17m · 120 g · 1 material(s)

    Prints on: P1S 0.4, P2S 0.4, A1 mini 0.4, H2D Pro 0.4, X2D 0.4, A2L 0.4, A1 0.4, H2D 0.4, X1E 0.4, X1 Carbon 0.4, H2S 0.4, X1 0.4, H2C 0.4, P1P 0.4PLA

    Not in stock

  • Corner Module v1 P2

    ⏱ 2h 18m · 120 g · 1 material(s)

    Prints on: P1S 0.4, P1P 0.4, A2L 0.4, X1E 0.4, H2D Pro 0.4, X1 0.4, A1 0.4, A1 mini 0.4, H2D 0.4, H2C 0.4, X1 Carbon 0.4, P2S 0.4, H2S 0.4, X2D 0.4PLA

    Not in stock

  • Corner Module v2 P1

    ⏱ 2h 11m · 115 g · 1 material(s)

    Prints on: P1S 0.4, H2D Pro 0.4, A2L 0.4, H2S 0.4, H2D 0.4, A1 mini 0.4, H2C 0.4, X1 Carbon 0.4, P2S 0.4, X2D 0.4, P1P 0.4, X1 0.4, X1E 0.4, A1 0.4PLA

    Not in stock

  • Corner Module v2 P2

    ⏱ 2h 11m · 115 g · 1 material(s)

    Prints on: P1S 0.4, X1E 0.4, P2S 0.4, H2C 0.4, H2D 0.4, A2L 0.4, X1 Carbon 0.4, A1 mini 0.4, X2D 0.4, H2D Pro 0.4, P1P 0.4, H2S 0.4, X1 0.4, A1 0.4PLA

    Not in stock

  • Middle Module v2

    ⏱ 2h 13m · 116 g · 1 material(s)

    Prints on: P1S 0.4, H2D 0.4, A1 mini 0.4, H2C 0.4, H2D Pro 0.4, X2D 0.4, X1 0.4, A2L 0.4, X1E 0.4, A1 0.4, X1 Carbon 0.4, P1P 0.4, H2S 0.4, P2S 0.4PLA

    Not in stock

  • Middle Module v1

    ⏱ 2h 18m · 121 g · 1 material(s)

    Prints on: P1S 0.4, A2L 0.4, P2S 0.4, H2C 0.4, A1 mini 0.4, H2D 0.4, X1 0.4, X1 Carbon 0.4, X2D 0.4, P1P 0.4, A1 0.4, X1E 0.4, H2S 0.4, H2D Pro 0.4PLA

    Not in stock

  • Container Basic v1

    ⏱ 1h 5m · 55 g · 1 material(s)

    Prints on: P1S 0.4, H2D 0.4, A1 mini 0.4, H2C 0.4, H2D Pro 0.4, X2D 0.4, X1 0.4, A2L 0.4, X1E 0.4, A1 0.4, X1 Carbon 0.4, P1P 0.4, H2S 0.4, P2S 0.4PLA

    Not in stock

  • Container Basic v2

    ⏱ 1h 16m · 66 g · 1 material(s)

    Prints on: P1S 0.4, H2S 0.4, X1 0.4, X1E 0.4, P2S 0.4, P1P 0.4, X2D 0.4, A1 0.4, H2D Pro 0.4, H2C 0.4, A2L 0.4, A1 mini 0.4, X1 Carbon 0.4, H2D 0.4PLA

    Not in stock

  • Container Basic v3

    ⏱ 1h 29m · 75 g · 1 material(s)

    Prints on: P1S 0.4, H2D 0.4, A1 mini 0.4, H2C 0.4, H2D Pro 0.4, X2D 0.4, X1 0.4, A2L 0.4, X1E 0.4, A1 0.4, X1 Carbon 0.4, P1P 0.4, H2S 0.4, P2S 0.4PLA

    Not in stock

  • Container Angled v1

    ⏱ 1h 3m · 49 g · 1 material(s)

    Prints on: P1S 0.4, H2D 0.4, A1 mini 0.4, H2C 0.4, H2D Pro 0.4, X2D 0.4, X1 0.4, A2L 0.4, X1E 0.4, A1 0.4, X1 Carbon 0.4, P1P 0.4, H2S 0.4, P2S 0.4PLA

    Not in stock

  • Container Angled v2

    ⏱ 1h 11m · 57 g · 1 material(s)

    Prints on: P1S 0.4, X1E 0.4, X1 0.4, H2D Pro 0.4, P2S 0.4, P1P 0.4, A1 0.4, X1 Carbon 0.4, A1 mini 0.4, H2D 0.4, H2C 0.4, X2D 0.4, A2L 0.4, H2S 0.4PLA

    Not in stock

  • Container Wide v1

    ⏱ 1h 43m · 94 g · 1 material(s)

    Prints on: P1S 0.4, X1E 0.4, H2D Pro 0.4, A1 0.4, A2L 0.4, X1 0.4, X1 Carbon 0.4, H2D 0.4, H2S 0.4, P1P 0.4, A1 mini 0.4, H2C 0.4, X2D 0.4, P2S 0.4PLA

    Not in stock

  • Container Wide v2

    ⏱ 1h 59m · 115 g · 1 material(s)

    Prints on: P1S 0.4, A1 mini 0.4, X1 Carbon 0.4, X1E 0.4, H2C 0.4, P2S 0.4, A2L 0.4, P1P 0.4, A1 0.4, H2S 0.4, X1 0.4, H2D 0.4, X2D 0.4, H2D Pro 0.4PLA

    Not in stock

  • Connector Piece

    ⏱ 11m · 1 g · 1 material(s)

    Prints on: P1S 0.4, X1E 0.4, H2D Pro 0.4, A1 0.4, A2L 0.4, X1 0.4, X1 Carbon 0.4, H2D 0.4, H2S 0.4, P1P 0.4, A1 mini 0.4, H2C 0.4, X2D 0.4, P2S 0.4PLA

    Not in stock

  • Connector Piece x4

    ⏱ 15m · 3 g · 1 material(s)

    Prints on: P1S 0.4, X1E 0.4, X1 0.4, H2D Pro 0.4, P2S 0.4, P1P 0.4, A1 0.4, X1 Carbon 0.4, A1 mini 0.4, H2D 0.4, H2C 0.4, X2D 0.4, A2L 0.4, H2S 0.4PLA

    Not in stock