This is a single-deck box designed with the Cyberpunk TCG in mind, especially for showing off your three legends along with being a decentlycompact storage box. Three of the four walls are display slots. Each one is designed for the Gamegenic Slide Case but should also fit the Ultra Pro Mini Snap case. The display slots take the same panels as the rest of my deck boxes — 95.6mm x 69.6mm x 5.6mm. Anything you've already printed for my Falcon boxes drops straight into this one, and the modular adapter and blanks on my profile fit all of them. The slots themselves are 70mm wide and 6mm deep with a floor 5mm up from the bottom, showing through a 66mm window, so it's easy enough to draw your own. The main compartment is 70mm x 78mm and 96mm deep. That's 78mm of card stack — for comparison, my Falcon One box gives 46mm. Going by the same sleeve thicknesses I measured there, that should be somewhere around 80-85 cards double-sleeved or 130-135 single-sleeved, but it'll depend heavily on your sleeves. There's a deep thumb scoop in three of the four walls to get the stuff out and you can orient the cards and gig dice holder how you like. I've included two versions of the lid: one with retaining notches that click into four sockets in the rim, and one without. Same trade-off as my other boxes — the notches latch it properly and are more of a nuisance to get on and off, and the plain lid is easier to live with but won't survive a shake test. There are four holes for 5x3mm magnets in the lid and four holes in the base. The base holes are designed to hold two 5x3mm magnets each, for a total of 12 magnets: four in the lid and eight in the base. I double-stacked the magnets in the base to get a slightly stronger hold, since the magnet surface area is pretty small. There are two different box/lid version, filleted and chamfered. They're the same box otherwise; every dimension the lid closes on is identical, so lids and bases are interchangeable between them. Accessories I've included in this upload that work with this box (and with my other boxes in my profile): The gig dice holder stands upright inside the box next to the deck. It's 69.2mm x 90.4mm and 26mm closed, so it drops in with a little room over its head and leaves about 52mm of card stack — call it 55 double-sleeved or 90 single-sleeved alongside six dice. Also the gig dice holder is meant to use 4 12x3mm magnets and give a pretty decent hold along with the notches to keep it from sliding around. If you feel the need to bling it out even more and need a slab holder I've included one (and the panel adapter) for you to go wild. I would recommend not using the notched lid (especially if you're using 3 slab holders) because it will be pain to get the non-notched lid off as it is and with that notched lid is 10x worse. Once those notches wear down a little it gets easier but no guarentees on how long that will take. I've printed this mainly on a Creality K2 Plus at 0.2mm layer height, with no supports and 15% infill. Two walls seem sufficient, but I've printed other boxes with three walls for added durability. Printed in PLA with generic settings. Everything prints in the orientation it's supplied in — base on its floor, lids with tops face-down on the plate. Should not need any supports for any of these items. For other accessories that may be compatible with this deck box, check the other prints on my profile.

Cyberpunk TCG Deck Box and Accessories

by vampyre · original on MakerWorld ↗

♥ 12⬇ 41🖨 12 prints

Print profiles

• Added logo to dice and deck box, tuned for Silk PLA

  ⏱ 3h 5m · 71 g · 2 material(s) · needs AMS

  Prints on: H2C 0.4, X1 Carbon 0.4, H2D Pro 0.4, X1 0.4, X2D 0.4, H2S 0.4, A1 0.4, X1E 0.4, A2L 0.4, H2D 0.4, P1S 0.4, P2S 0.4, A1 mini 0.4, P1P 0.4PLAPLA

  Not in stock

• 0.2mm layer, 2 walls, 15% infill

  ⏱ 14h 38m · 565 g · 1 material(s)

  Prints on: P2S 0.4, H2C 0.4, H2D Pro 0.4, P1P 0.4, X2D 0.4, A1 0.4, X1 0.4, X1 Carbon 0.4, H2S 0.4, A2L 0.4, X1E 0.4, P1S 0.4, H2D 0.4PLA

  Not printable on our printers