================================ This is a collaborative full‑function CyberBrick‑compatible radio‑controlled combat vehicle project! Development kicked off back in May, and after four months of work, we’re thrilled to finally share it with the community. 🤝 Co‑creators: collor, XYCJ, Bavaria_3D Tanks Huge thanks to everyone for their fantastic contributions to make this project happen! This release is a pure 3D‑print‑only version with no additional purchased parts required. CyberBrick mechatronics components are not supported in this build. If you’d like the motorized CyberBrick variant, please head over to collor’s profile page. https://makerworld.com/en/@collor EBR 1954 4WD Remote Control Armored Reconnaissance Vehicle · Motorized Rotating and Tilting Turret · Independent Suspension · CyberBrick Compatible: https://makerworld.com/en/models/3277538-ebr-1954-4wd-remote-control-armored-reconnaissance#profileId-3717190 ================================ 📋 Recommended Print Settings (For Best Results) Filament: PLA. Different materials have different shrink rates, so using other filaments might cause fitting issues or dimensional errors during assembly. Slicer: Bambu Studio. I recommend using my default profile — I’ve tuned it specifically for this model. Ambient Temperature: If you’re using an open-frame printer like the A1 or A1 Mini, keep your room above 20°C (68°F) to prevent warping. Print Bed Preparation: Wash with soap and water, then dry thoroughly to ensure good adhesion. For small parts, apply a glue stick for better bed adhesion. 🔧 Assembly Diagram Notes Blue Lines: Require super glue for assembly. I use Gorilla Super Glue. Yellow Lines: These are moving parts. Do not apply glue here.

Panhard EBR (1954) Armoured Vehicle 1/35 Scale

by Bavaria_3D Tanks · original on MakerWorld ↗

♥ 584⬇ 280🖨 227 prints

Print profiles

• EBR1954 With AMS

  ⏱ 12h 29m · 195 g · 4 material(s) · needs AMS

  Prints on: A1 mini 0.4, X1 Carbon 0.4, H2C 0.4, A2L 0.4, P1S 0.4, H2D Pro 0.4, P2S 0.4, X1E 0.4, H2D 0.4, P1P 0.4, H2S 0.4, X1 0.4, X2D 0.4, A1 0.4PLAPLAPLAPLA

  Not in stock

• EBR1954 Non-AMS

  ⏱ 10h 50m · 179 g · 3 material(s)

  Prints on: A1 mini 0.4, X1 Carbon 0.4, X1E 0.4, H2C 0.4, P2S 0.4, A2L 0.4, P1S 0.4, P1P 0.4, A1 0.4, H2S 0.4, X1 0.4, H2D 0.4, X2D 0.4, H2D Pro 0.4PLAPLAPLA

  Not in stock

• [Monochrome / AMS] 1:35 Decorative Tool Set Fixed

  ⏱ 31m · 5 g · 2 material(s) · needs AMS

  Prints on: A1 mini 0.4, H2C 0.4, A2L 0.4, X1 Carbon 0.4, A1 0.4, P1S 0.4, X2D 0.4, X1E 0.4, P2S 0.4, X1 0.4, H2S 0.4, H2D Pro 0.4, P1P 0.4, H2D 0.4PLAPLA

  Not in stock