🖨️ Print Shop
Pottery Centering Tool for Trimming - Fixed Pins

This is a tool to centre and hold pots on a pottery wheel for trimming/glazing/sanding. It has three sliders which move in towards the middle at the same rate, which ensures the pot is held in the middle of the wheel. It attaches to the wheelhead with batt pins, and this is designed for wheels with 10mm and 9.5mm pins at 254mm (10ich) and at 148mm (If your wheel has different pin spacings or no pins at all, there are other models available). There is a printable hole checker that you can print first, to check that the standard holes will work with your wheel. Pick the print name that matches your wheel direction. Designed to print on a standard 256mm build plate with no supports and no hardware required. To assemble the tool: Bottom plate has the spiral facing up. Top plate sits on top with screw thread downwards through the hole in the bottom plate. Put the angled nut on the screw thread and tighten with the printed tool (should be done up tight, and this shouldn't stop the plates from spinning). The sliders are reversible, with a smaller and a larger side. They get inserted at the outer end of the slot in the top plate, and can only go in at the correct point in the rotation

Pottery Centering Tool for Trimming - Fixed Pins

by Old Forge Creations · original on MakerWorld ↗

♥ 413⬇ 756🖨 571 prints

License: MakerWorld Exclusive Licensepotteryceramicstoolthree-jaw chuck

Print profiles

  • P1S - no objects in exclusion area

    ⏱ 8h 33m · 320 g · 1 material(s)

    Prints on: P1S 0.4, X1E 0.4, X1 0.4, H2D Pro 0.4, P2S 0.4, P1P 0.4, A1 0.4, X1 Carbon 0.4, H2D 0.4, H2C 0.4, A2L 0.4, H2S 0.4, X2D 0.4PLA

    Not printable on our printers

  • Tuned, Arachne Wall, Top Ironing

    ⏱ 8h 16m · 325 g · 1 material(s)

    Prints on: P2S 0.4, H2S 0.4, A1 0.4, A2L 0.4, H2D Pro 0.4, H2D 0.4, H2C 0.4, X2D 0.4PLA

    Not printable on our printers

  • Full Print Anticlockwise - One Colour - Version 1

    ⏱ 7h 4m · 320 g · 1 material(s)

    Prints on: P2S 0.4, H2D Pro 0.4, A1 0.4, H2D 0.4, H2C 0.4, A2L 0.4, H2S 0.4, X2D 0.4PLA

    Not printable on our printers

  • Full Print Clockwise - One Colour - Version 1

    ⏱ 7h 5m · 320 g · 1 material(s)

    Prints on: P2S 0.4, A2L 0.4, H2D Pro 0.4, A1 0.4, H2D 0.4, H2C 0.4, H2S 0.4, X2D 0.4PLA

    Not printable on our printers

  • Anticlockwise - 10mm Holes - Version 2 Full Print

    ⏱ 7h 9m · 339 g · 1 material(s)

    Prints on: P1S 0.4, H2D Pro 0.4, H2S 0.4, P2S 0.4, X1 Carbon 0.4, P1P 0.4, H2D 0.4, X1E 0.4, A1 0.4, H2C 0.4, X1 0.4, A2L 0.4, X2D 0.4PLA

    Not printable on our printers

  • Anticlockwise - 9.5mm Holes - Version 2 Full Print

    ⏱ 7h 9m · 339 g · 1 material(s)

    Prints on: P1S 0.4, X1 0.4, A1 0.4, X1E 0.4, P2S 0.4, H2D 0.4, A2L 0.4, H2C 0.4, X1 Carbon 0.4, H2D Pro 0.4, H2S 0.4, P1P 0.4, X2D 0.4PLA

    Not printable on our printers

  • Clockwise - 10mm Holes - Version 2 Full Print

    ⏱ 7h 10m · 339 g · 1 material(s)

    Prints on: P1S 0.4, H2C 0.4, H2D Pro 0.4, P1P 0.4, X1 0.4, A1 0.4, X1E 0.4, X1 Carbon 0.4, H2S 0.4, P2S 0.4, A2L 0.4, H2D 0.4, X2D 0.4PLA

    Not printable on our printers

  • Clockwise - 9.5mm Holes - Version 2 Full Print

    ⏱ 7h 10m · 339 g · 1 material(s)

    Prints on: P1S 0.4, H2D 0.4, P2S 0.4, H2C 0.4, H2S 0.4, X1E 0.4, X1 Carbon 0.4, A1 0.4, P1P 0.4, X1 0.4, H2D Pro 0.4, A2L 0.4, X2D 0.4PLA

    Not printable on our printers