Dremel 4000 Wall mount with drill tool bits storage. The Dremel tool can be stored either way up/down depending on your preference.
An additional section can be printed to expand your wall mount if required and can be mounted to the right and/or to the left of the Main unit.
Prints without supports.
(Will require 6mm x 2mm strong magnets)
I have added some tabs that can be used to glue into place of magnets if you prefer something more permanent.
(There is a separate file for a Dremel 3000 which is untested by me as I don't own one. Feedback welcomed)
*Update: Peg Board adaptors have been added. These are untested as I don't have a Peg Board. You will need to screw them into the Main wall mount at the top and also add the spacers at the bottom.
**Update: Dremel original case holder Extension. To be attached to the Left side. Can be mirrored in Slicer to attach to the right if preferred. I would recommend gluing this one on as it could be a bit too heavy for the magnets alone. (Print using Brim as surface contact is low)
Dremel 4000 Wall mount with drill tool bits storage
by Mike · original on Printables ↗
Hobby & Makers / Organizers
♥ 1.5k⬇ 3.5k🖨 19 prints
Print profiles
Dremel Ext1 for Right Side.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Glue Tabs.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Dremel Main.stlDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Peg Board Right.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Peg Board Left.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Peg Board bottom Spacer .stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Dremel Ext3.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Dremel Ext Case holder.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Dremel 3000.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Dremel Ext2 For Right Side.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Dremel Ext2 For Left Side.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Dremel Ext1 for Left Side.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print