3.5" to 2.5" adapters, made for mounting 2.5" devices to 3.5" mounts.
The bottom drive can also be mounted on the bottom with counter sunk screws.
The 3.5" holes are sized to hold well using 6#-32 UNC screws that are usually install with the hard drive.
Note: The connectors will not line up with the original 3.5" hard drive, so this is not usable with a sledge design where the connectors are hard mounted to the case. Only cable connections.
Sizes:
3.5 to 2.5 mount - 3xSSD (7mm)
Original model, made for stacking 3 SSDs (7mm height) within the height of a 3.5" device.
3.5 to 2.5 mount - 3x10mm
Extended height model, 30.6mm tall if 7mm device is installed on top mount, so it exceeds the height of a 3.5" device.
3.5 to 2.5 mount - single
Single 2.5" device mount, practicly not limited by height :)
3.5 to 2.5 mount - 2x12.5mm
Dual mount for taller devices if needed, will exceed height of 3.5" device if taller than 10.5mm height 2.5" device is mounted in the top mount.
If there are any issues or other sizes you require send me a message or comment and i will see what i can do :)
Change log:
V1: Original release.
V2: Corrected spacing of bottom 3.5" mounting holes.
V3: Added third set of bottom 3.5" mounting holes and more sized for different needs.
V4: Extended 2.5" mounting holes upwards to make mounting a bit more flexible.
3.5" to 2.5" adapters
by Slaur · original on Printables ↗
Gadgets / Computers
♥ 346⬇ 1.1k🖨 6 prints
Print profiles
3.5 to 2.5 mount - 3xSSD (7mm) v3.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
3.5 to 2.5 mount - 3x10mm v3.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
3.5 to 2.5 mount - single v3.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
3.5 to 2.5 mount - 2x12.5mm v3.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
3.5 to 2.5 mount - 2x12.5mm v4.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
3.5 to 2.5 mount - 3x10mm v4.stlDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
3.5 to 2.5 mount - single v4.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
3.5 to 2.5 mount - 3xSSD (7mm) v4.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print