This is the full kit to raise the Creality K1C lid to minimise/ eliminate the issue of cable chain bumping onto the lid when printing at the left edge (when viewing the Creality K1C from the front).

It also eliminates the issue of extruder bumping into the corner support when printing at the corner where the K1C camera is located.

If you frequently print with the lid open and find that it is wobbling a little too much during high speed prints, perhaps you need the Lid Supporter add-on for Creality K1/K1C Hinged Lid Raiser. It is just an additional piece to be attached on each of the hinged corner piece.

Add-on or Upgrades to the Creality K1/K1C Hinged Lid Raiser

Features

Full print on one (1) bed (220 x 220mm)
No supports required
No bed adhesion required (i.e., autobrim, raft)

Additional parts required

Four M3x30 screws to secure the corner pieces (optional but recommended)

My print configuration

Material: PLA
Infill: 30%
Infill Pattern: Grid
Supports: No
Brim/ Raft: None

Change Log

v2 (04 May 24) - Created a new corner (camera side, v2) to further reduce the bumping of the cable chain attachment. Added requested STL for hinged back corners.
v1 (18 Feb 24) - Initial release.

Enhancements to the original design

The corner support piece above the Creality K1C camera has been made thinner at some section to eliminate the issue of extruder bumping into the corner support when printing at the corner;
The rear betweener now fits properly as the original piece does not fit the cable chain holder/ bowden tube anchor piece (to the K1C frame);
The rear betweener has been extended to cover the groove at the rear of the lid

Link to original design: https://www.printables.com/model/525295-jc-creality-k1-hinged-lid-riser

Creality K1/K1C/K1SE Hinged Lid Riser

by shadowandy · original on Printables ↗

3D Printers / Creality Parts & Upgrades

♥ 831⬇ 11.0k🖨 68 prints

License: Creative Commons — Attribution — Noncommercial — Share Alike ↗lidhingecrealityraiseropeningriserhingedk1crealityk1ck1cshadowandycrealityk1cmodk1se

Print profiles

Creality K1C Hinged Lid Riser Kit (v1).stlDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Creality K1C Lid Riser Betweener - Back (Hex).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Creality K1C Lid Riser Betweener - Sides (Hex).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Creality K1C Lid Riser Betweener - Sides (Filled).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Creality K1C Lid Riser Betweener - Back (Filled).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Creality K1C Hinged Lid Riser - Camera Corner (v1).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Creality K1C Hinged Lid Riser - Pins.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Creality K1C Hinged Lid Riser - Camera Corner (v2).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Creality K1C Hinged Lid Riser Kit (v2).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Creality K1C Hinged Lid Riser - Hinged Back Corners.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print