-Uses six M3x20 screws for the hinges and latch.
-Uses two 3mm x 1mm magnets for the small parts storage compartment (optional).
Storage for:
1 x Pinecil (TS100/TS101 BETA versions still testing)
7 x Short Tips (6 x Tips for TS100/TS101 due to dimensional differences)
1 x Long/Short Tip (installed in soldering iron)
1 x Flux Syringe (1 ml) OR Flux Syringe (6 ml) OR Alternate Large Slot
1 x Magnetic Storage Compartment for Small/Spare Parts (Need Four 3mm x 1mm Magnets)
1 x 608 Bearing Stand (from V2 stand from Termiman or my remixed version)
2 x Solder/Ribbon Spools from Termiman
1 x Slot for Wet Sponge
1 x Slot for Brass Sponge
1 x Slot for 1.5m USB-C Cable
INFO & TIPS:
-To load up your own 1ml oral syringe; you can melt flux until liquid (with a hair-dryer or heatgun) and suck it up.
-The 4 magnets (3mm x 1mm) for the storage container, might need a dab of superglue. I tried to make a magnet-less hinge and compliant latch, but there isn't a ton of room to work.
PINECIL & TS100/101 ALL-IN-ONE CASE
by TheCafeRacer · original on Printables ↗
Hobby & Makers / Tools
♥ 448⬇ 2.2k🖨 29 prints
Print profiles
GASKET.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
LID (LOGO).3mfDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
LATCH.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
BASE.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
LID (NOLOGO).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
STORAGE LID.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
LID (PINECIL LOGO).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
PINECIL_1ML SYRINGE INSERT (BASE).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
PINECIL_6ML SYRINGE INSERT (BASE).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
PINECIL_LARGE SLOT INSERT (BASE).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
TS100_6ML SYRINGE INSERT (BASE).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
TS100_LARGE SLOT INSERT (BASE).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
TS100_1ML SYRINGE INSERT (BASE).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
LID (PINECIL CUTOUT).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
7-TIP INSERT (PINECIL SHORT TIPS).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
LID (MINIWARE CUTOUT).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
6-TIP INSERT (TS100 SHORT TIPS).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print