Please comment, rate, and post a make!
Update 1/19/2024: I've added a new back with a ball joint to give better flexibility with printing a single back for multiple mounting options.
A simple case for using an LD2410C radar sensors with an ESP32 S2 Mini. I've included a little spacer that can be slid over the pins of the LD2410C to help with soldering to the ESP board. The lid has a cutout for the light sensor and the case body has holes for accessing the reset and programming mode buttons.
BOM (affiliate links):
- S2 Mini
- LD2410C
- USB Cable
- Something to mount them to the wall with:
- My preference is Gorilla Putty but a small Command strip should work just as well.
I'm using the this YAML configuration to integrate with Home Assistant.
- Slide the spacer over the pins on the LD2410C
- Solder the LD2410C to the ESP32.
- Trim the pins on the back of the ESP32 as flush to the board as possible.
- Slide the board into the case:
- Put the side with the radar in first. There's a lip on the inside of the case that the ESP board should sit on.
- Lower the rest of the board into place.
- Pop on the back cover.
Be sure to check out my other models!
Case for ESP32 S2 Mini and LD2410C
by TheProjectWheel · original on Printables ↗
Gadgets / Other Gadgets
♥ 103⬇ 869🖨 4 prints
Print profiles
Flat Back.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Right Angled Back.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Down, Left, or Right Angled Back.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Ceiling Corner Back.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
ESP32-S2 Mini and LD2410C.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Left Angled Back.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Corner Back.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Spacer Pin.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Case.stlDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Ball Joint.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print