Remix of VoyMakesMinis' Necron Obelisks (or Objective Markers) found here: https://www.printables.com/model/470609-necron-obelisks-or-objective-markers

I hollowed their model with supports to be able to house an LED and resistor and paired it with my own 40mm base with battery housing.

I've included the little support tower I printed to fit the LED on but truthfully I would probably use some toothpicks if I do it again, the legs broke multiple times before it was all done.

Should not need any supports though you might find a brim helpful.

Remixed in Tinkercad

Update:

I've added the other Obelisk from VoyMakesMinis' now also hollowed out. To Print this one successfully I had to break it into 2 parts. The Middle can be printed lying down and the 2 halves of the outer shell can printed upright, they are joined with supports to cut after printing. You will likely need to glue these in place so I recommend priming and doing any other spray painting before assembling with LEDs to avoid covering your lights with paint since they will be tough to mask after assembly.

LED Necron Obelisk

by CottonsCreations · original on Printables ↗

Tabletop Miniatures / Props & Terrains

♥ 185⬇ 685🖨 2 prints

License: Creative Commons — Attribution — Noncommercial ↗ledmarkerwarhammerwarhammer40knecronobjectivelightup

Print profiles

Necron Objective Marker LED 1.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Necron Objective Marker LED 1 Support tower.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Necron Objective Marker LED 1 Base Fitting.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
40mm Base.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
40mm cr2032.stlDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Necron Objective Marker LED 2 Slanted Base Fitting.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Necron Objective Marker LED 2 Base Fitting.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Necron Objective Marker LED 2 Outer.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Necron Objective Marker LED 2 Inner.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Necron Objective Marker LED 1 Slanted Base Fitting.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print