FOR PERSONAL USE ONLY
Cutters are in two parts, 'outline' (for a shape) and 'insert' (for more details)
Cookies will have around 6cm
---
Made in Blender 3D
Printed on Voron0.1 with Vanilla White PLA - Prusament
Short video from baking
https://www.instagram.com/p/Cr0mW34gYjT/
---
Best with low growing dough
I used it with butter cookies (recipe on the bottom)
If you want you can use a simple glass or any other shape bigger than this cookie cutters, cut the shape with it and just mark the lines on the cookie with cookie cutters (taking care of not cutting through the dough with 'outline')
You can make bigger cookies after resizing the models but cutting with it will be a little harder
Clean the print up before using cutters
Cut / burn strings etc.
It is good to wash it before and after use
Models by difficulty of using from easiest to hardest:
Star-1
Star-0
Falcon
Destroyer
X
Tie (be really carefull when unsticking dough from insert)
Update 01 V 2023
Version 1.2 of Tie with bigger middle part - will be easier to use
Changed Star-0b insert middle part to be the same as in Star-0a insert
Added all models render with names to images
Update 01 V 2023
X and Falcon outline models are now with proper wall thickness (0.8mm instead of 0.4)
---
Check my Cookie cutters collection on Printables:
https://www.printables.com/@C47_3d/collections/147977
or more on:
https://cults3d.com/en/design-collections/c47/cookie-cutters
---
Butter cookies recipe
300g (~10.6 oz) wheat flour
150g (~5,3oz) butter
70g (~2,5oz) powdered sugar
1 egg, cold
1 small flat spoon of baking powder
pinch of salt
You can add 30g (~1oz) of cocoa for chocolate taste. Use 30g (~1oz) LESS flour and 10g (~0.33oz) MORE sugar then
Mix everything until fully combined. Put in the fridge for at least 1 hour.
Then knead it for a while, pin out the dough to around 5mm (~0.4") and cut the shapes with cookie cutter.
Bake with 180*C (~355*F) - with both top and bottom heaters on - for few minutes (depends on dough thickness, oven and it's settings) - I baked mine for about 6-7min. Pull them out when they will get a darker color on top.
---
PRINT SETTINGS
Made for 0.4mm nozzle. Lines on the 'Outline' are 2x0.4mm
Use 2-3 walls and some more infill (like 25% or more - it makes the marking the lines with 'Insert' easier)
At least 1mm on the top and bottom layers (again for easier use and strenght)
0.2mm layer height (but highier or lower may be good too)
Star Wars Cookie Cutters Set
by C47_3d · original on Printables ↗
Household / Kitchen
♥ 308⬇ 1.0k🖨 13 prints
Print profiles
SW-cookie_Star-1_outline.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_Star-0_outline.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_Destroyer_outline.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_Destroyer_insert.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_Tie_outline.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_Falcon_insert.stlDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_Star-0a_insert.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_X_insert.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_Tie_insert.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_Star-1_insert.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_Tie_outline_v12.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_Tie_insert_v12.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_Star-0b_insert.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_X_outline.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
SW-cookie_Falcon_outline.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print