This works well for my PSVR2. There are a few choices for the base that add extra weight in the front to reduce tipping over backwards. See the STL files for the base choices.
I printed the simple ‘front bar’ one at first and then the black & white layer change solid bottom (no logo) one. There is also another more solid one but with ‘VR’ text embossed into it - not PS branded, just generic ‘VR’.
3/4/23: Added two more bases - thick bottoms. One with a VR logo, the other without.
2/26/23: Added two more base versions that use a small lip at the front so the base has a little ‘tray’ that you can put things like spare parts for your DualSense Edge controller or those silicon ear bud alternate sizes. Just a place to keep them handy. I just printed this one for my final version for personal use.
I printed mine at .28 height / .52 line width with a .4 nozzle / 50% grid infill (for more weight only) and at 90mm/s.
The original suggested using M4x16 screws. I didn't have them, so I ended up using M4x20 self-tapping screws and they worked well.
You can also just use the holes to align the top and base while you apply CA glue.
- Feb 28 - Added two alignment ‘pegs’ to help those without screws.
- The round ones print vertically, but will be weaker. The ones that have flat sides and print horizontally should be a bit stronger, but the caps will look ‘weird’ and give a lot more wiggle room and will need more attention to center. I think the glue on the base will be all the strength you need, so I would use the round ones if I didn't have screws to use.
- Either way, to use these, print two and check the fit and resize in your slicer if you feel you want more or less of a tight fit. Add some CA glue to the base top and then some to each peg before inserting. Insert the pegs, eyeballing the centering a little may be needed, and then just hold for a few seconds until the glue sets enough to hold it for you.
I also used 5 clear rubber cabinet bumpers (about ½") for anti-slip on the bottom of the stand. Any similar type can be used of course.
Images note: the solid base one (no logo) on the PS5 box has the base printed with a layer change so it starts black and then white and then the top is printed black. It is still the 2 part stand.
Playstation VR2 (PSVR2) Headset Stand (updated Mar 4)
by psybertech · original on Printables ↗
Gadgets / Virtual Reality
♥ 313⬇ 1.7k🖨 37 prints
Print profiles
PSVR2 Headset base - solid NO LOGO.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
PSVR2 Headset base - solid basic VR LOGO.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
PSVR2 Headset base - bar - minimal.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
PSVR2 Headset Top (bed-rotated).stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
PSVR2 Headset base v2 - Storage Tray - NO LOGO.stlDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
PSVR2 Headset base v2 - Storage Tray - LOGO.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
PSVR2 Headset 3.5mm Alignment Peg - Flat.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
PSVR2 Headset 3.5mm Alignment Peg.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
PSVR2 Headset THICK BASE v2.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
PSVR2 Headset THICK BASE LOGO v2.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print