Updates description at the bottom
Overview
A model of a variable pitch propeller mechanism based on a 1935 patent by Robert Stanley, adapted for 3D-printing.
Variable pitch propellers allow the pilot of an airplane to adapt the angle of the blades according to the speed of the airplane for optimal performance. While most variable pitch propeller systems use hydraulic or electric power, this purely mechanical system uses two planetary gears to control the pitch of the blades on the rotating propeller from a driving gear on the stationary housing.
Using 3D-printing allows for these planetary gear assemblies to be made with print-in-place herringbone gears (impossible to disassemble), which simplifies tremendously the assembly process.
See the mechanism in action :
I included pages of the original patent if you want to read the details.
This system was used on the Curtiss Turboelectric propellers that equipped the Douglas C-133 Cargomaster.
Parts
All parts are 3D-printed. No additional hardware is necessary. The whole assembly is held by three 3D-printed nuts.
You will need to print :
Propeller assembly
- 1 x front-hub (or front_hub_alt, see update Oct 11th)
- 1 x rear-hub (or rear_hub_alt, see update Oct 11th)
- 1 x hub-nut
- 5 x blade
- 5 x spur-worm-gear
- 5 x thust-washer
Housing and shaft assembly
- 1 x front-housing
- 1 x rear-housing
- 2 x bearing-1 (see note 1)
- 1 x shaft
- 1 x spacer-1
- 1 x rear-nut
Final assembly
- 1 x rear-planetary-assy
- 3 x planet-axis
- 1 x spider
- 1 x front-planetary-assy
- 1 x spacer-2
- 1 x bearing-2 (see note 1)
- 1 x spacer-3
- 1 x control-gear (or control-gear-alt, see note 2 below)
- 1 x blade-setting-crank
- 1 x front-shaft-nut
- 1 x motor-crank
And the (optional) tools:
- 1 x front-shaft-nut-socket-wrench
- 1 x hub-nut-spanner
- 1 x rear-nut-spanner
I built all parts from PLA with 0.2mm layers using the default Prusa Mk3S profile. Only the rear housing requires supports.
Notes :
- I did not manage to get the bearings to run for real, both for bearing 1 and bearing 2 the rollers are either stuck to the cage or they have too much friction so the rollers don't really roll, the best I could do in the limited time before the contest deadline was to have the inner and outer rings move freely. This does not prevent the mechanism from functioning properly.
- The mechanism was designed for a 20-tooth control gear, but because of freeplay in the assembly, on my prototype it tends to slip easily on the external gear of the front planetary assembly. So on my assembly a 21-tooth control gear which was theoretically too large gave the best results and is therefore provided as an alternative (control-gear-alt) if you encounter the same problem.
Instructions
See the build video :
Exploded views
Propeller assembly
Housing and shaft assembly
Final assembly
Reminders :
- Don't tighten the nuts too much, it's only plastic !
- Some gears and bearings will require a bit of breaking in before they run smoothly so be sure to do this before final assembly in order for things to run properly without overstressing the parts.
Design notes
Information that may be useful for remixes :
All the gears have a module of 1 and a contact angle of 20°.
The planet gears are scaled down to 97% in lateral and vertical to give enough clearance to print the planetary assemblies "in-place".
Updates
October 11th, 2022: New propeller hub
I designed an alternative propeller hub (file names front_hub_alt and rear_hub_alt), that works exactly like the original but looks much better.
The new parts are however a bit harder to print and you will need to use supports.
The only difference in the assembly is that now the thrust washers have to be inserted in the small side slots on the rear hub rather than from its front face.
Variable Pitch Propeller Mechanism
by Chris B · original on Printables ↗
Learning / Engineering
♥ 2.3k⬇ 4.5k🖨 23 prints
Print profiles
control_gear_v2.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
blade_setting_crank.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
front_housing_v1.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
motor_crank_v1.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
front_shaft_nut_v3.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
spacer-1_v1.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
rear_housing_v1.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
front-shaft-nut-socket-wrench.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
front_hub_v2.stlDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
thrust-washer_v2.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
hub-nut-spanner.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
spacer-2_v2.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
spider_v1.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
hub_nut_v1.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
blade_v1.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
spur-worm-gear_v4.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
rear_nut_v2.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
bearing-2_v4.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
spacer-3_v1.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
rear-nut-spanner.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
planet_axis_v2.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
bearing-1_v5.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
shaft_v1.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
rear_hub_v1.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
front-planetary-assy_v4.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
rear-planetary-assy_v2.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
control_gear_alt.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
front_hub_alt.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
rear_hub_alt.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
rear_housing.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
rear_hub_alt.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
front_hub_alt.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print