Updated 27.03.2024
Pitch of the camera is now indexed in 8° steps. Â
New files are marked with “27032024”
Updated 18.06.2022
Added wall bracket variant to use with micro usb breakout PCB.
Prinitng
- Case front and wall bracket have to be printed with bed supports
- All other parts are optimized to print w/o supports
- Use finer layer height for better look of the case front (0.15 recommended)
Assembly
- Figure out the orientation of the housing with respect to the swivel (at the moment esphome will not allow for image rotation, so rotate the housing appropriatly)
- Drill a hole (3-4mm) for the wires in one of 4 spots on the sides of the case front part
- Push wall bracket connector into wall bracket, this requires a bit of force
- Run the wires, see the photo for reference
- solder (or otherwise connect) the wires to esp32cam
- place the esp32cam into case front, run the wires out of freshly drilled hole
- run the writes through the case swivel
- run the wires through wall bracket connector and then into the wall bracket
- Assemble the housing
- press the case swivel onto wall bracket connector
- press case rear into case front
- put the case front/rear assembly  into the case swivel
Installation
- Use a 1-3 screws or two sided tape to attach wall mount to a wall (use a wall plug for drywalls etc.)
- Hang the camera assembly onto the wall mount, it just slides on top.
- Plug the power supply in and enjoy.
Housing for esp32 cam
by Anverx · original on Printables ↗
Gadgets / Photo & Video
♥ 92⬇ 577🖨 4 prints
Print profiles
Esp32cam case swivel 2dof.stlDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Esp32cam wall bracket.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
esp32cam case rear.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Esp32cam wall mount.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Esp32cam case front.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Esp32cam wall bracket connector.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Esp32cam wall bracket USB.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
esp32cam case rear deeper 27032024.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Esp32cam case swivel 27032024.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Esp32cam case front 27032024.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print