This is a quick snap clamp for your mobile phone. The phone snaps in place with one move.

To connect the moving parts together use small pieces of filament. The base slides into the mounting part and locks with a piece of filament through the small hole. You will also need an M5 allen bolt and a nut to mount it on your handlebar. There are two versions depending on the phone width, and three different mounting options (two for handlebar and one for stem).

Although the clamp snaps firmly, it is advised to use small rubber bands or pieces from tubes (28mm road tubes) at the point where the arms touches phone, to ensure it doesn't slip at all.

Acknowledgments
Handlebar 3d model by Semyon Filippov
Mobile Phone 3D model by sillywilly

From BlendSwap.

Snapping Handlebar Mobile phone Clamp

by Stamos · original on Printables ↗

Sports & Outdoor / Outdoor Sports

♥ 260⬇ 610🖨 13 prints

License: Creative Commons — Attribution — Noncommercial ↗holdermountphoneclampbicyclequickhandlebarcompliantmobilephonebistable

Print profiles

Left_Lever 74-80.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Center_Part 74-80.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Right_Lever 74-80.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Handlebar_Mount 25.4.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Left_Lever 70-74mm.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Handlebar_Mount 31.8.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Right_Lever 70-74mm.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Center_Part 70-74mm.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Handlebar_Mount_low_profile_25.4.stlDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Handlebar_Mount_low_profile_31.8.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
Stem_Mount.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print