CArts Lukisegler

!! Attention !!

There is an updated version of the fuselage of the Lukisegler:
https://www.printables.com/de/model/927540-lukisegler-20-electrical-rc-glider

CArts Lukisegler (english)

Span: approx. 1700 mm
Body length: approx. 1000 mm
Take-off weight (LW-PLA): approx. 650 g
Take-off weight (PLA / PETG): approx. 1050 g
Drive: brushless motor
Propeller : folding propeller
Battery: 3S-4S Lipo 1000-1300 mAh
Controls: elevator / rudder / aileron / motor
Center of gravity: 70-75 mm behind the profile nose
Rudder deflections: 15-20 °

The CArts Lukisegler is an electrically powered glider that comes entirely from the 3D printer.

The design is most closely based on a hotliner. As a pilot you should have some experience, as in my opinion 3d-printed models are not suitable for beginners.

The complete building-instructions can be downloaded from my website:
https://c-arts-modelle.de/carts_modelle_web/fluggeraete/carts_lukisegler/carts_lukisegler.html
(It is a german website, but the translator in Chrome or Chromium will do quite a good job!)

The Lukisegler can be printed from PLA, PETG or lightweight PLA (LW-PLA). The construction of the parts is designed for a minimum of retracts is necessary when printing. This minimizes stringing especially when using PETG or LW-PLA.

The individual parts should also be printed individually. Otherwise the stringing will be too strong and the post-processing of the parts will be too time-consuming.

Modifiers are used in the print files . These are essential for the stability and for the structure of the individual parts! The surfaces for connecting the individual parts are made by using modifiers .

Required accessories

Parts for the construction

Carbon rods or fiberglass rods as well as various adhesives are required for the construction.

Adhesives

Superglue, low viscosity
Medium-viscosity superglue
5-minute epoxy resin

Carbon rods

Carbon rod 1 mm: 2 pieces (1000 mm length)
Carbon rod 1.5 mm: 5 pieces (1000 mm length)
Carbon rod 2 mm: 6 pieces (1000 mm length)

Steel wire

Steel wire 1 mm: 2 pieces (1000 mm length)

Magnets

Neodymium magnet round 8x2 mm (d x h): 1 piece

Screws

Wood screws 2x10 mm (d x h): 26 pieces
Screw M3x20 mm: 1 piece
Screw M3x30 mm: 1 piece

Electronics

Servos

Micro servos: 4 pieces (maximum dimensions (L x W x H) 23.5 x 10 x 24 mm)
9g Mini-Servos can be used in the fuselage with a updated servo plate:
https://www.printables.com/de/model/204579-lukisegler-electric-rc-glider-update-servoplate-fo

I use high quality servos with metal gears. These can cope with even greater loads (e.g. in the event of undesired contact with the ground) without damage. The additional costs for this are worthwhile.

Receiver

Minimum: 5 channels

Engine

Brushless motor (maximum dimensions (d x H) 28 x 50 mm)

ESC (controller)

Minimum: 20A (3-4S)
BEC minimum: 2A

How I set up Prusaslicer for my printer:

How to add modifiers and paint on seams in Prusaslicer:

CArts Lukisegler (deutsch)

Spannweite: ca. 1700 mm
Rumpflänge: ca. 1000 mm
Abfluggewicht (LW-PLA): ca. 650 g
Abfluggewicht (PLA / PETG): ca. 1050 g
Antrieb: Brushless-Motor
Luftschraube: Klappluftschraube
Akku: 3S-4S Lipo 1000-1300 mAh
Steuerung: Höhe / Seite / Quer / Motor
Schwerpunkt: 70-75 mm hinter der Profilnase
Ruderausschläge: 15-20°

Der CArts Lukisegler ein Segler mit Elektroantrieb, der vollständig aus dem 3D-Drucker kommt.

Die komplette Bauanleitung gibt es auf meiner Website: https://c-arts-modelle.de/carts_modelle_web/fluggeraete/carts_lukisegler/carts_lukisegler.html

Das Design ist am ehesten an einen Hotliner angelehnt. Als Pilot sollte man etwas Erfahrung mitbringen, da meiner Meinung nach 3d-gedruckte Modelle nicht für Anfänger geeignet sind.

Der Lukisegler kann aus PLA, PETG oder Lightweight-PLA (LW-PLA) gedruckt werden. Die Konstruktion der Teile ist so ausgelegt, dass beim Druck ein Minimum an Retracts nötig ist. Dies minimiert das Stringing beim Druck. Gedruckt wird mit einer 0,4mm Düse und einer Lagenhöhe von 0,2mm.

Die einzelnen Teile sollten auch einzeln gedruckt werden. Sonst wird das Stringing zu stark und die Nachbearbeitung der Teile wird zu aufwändig.

In den Druckdateien werden Modifier verwendet. Diese sind essentiell wichtig für die Stabilität und für den Aufbau der einzelnen Teile!

Benötigtes Zubehör

Teile für den Aufbau

Für den Aufbau werden Carbon-Stäbe bzw. Glasfaser-Stäbe sowie verschiedene Klebstoffe benötigt.

Klebstoffe

Sekundenklebstoff dünnflüssig
Sekundenklebstoff mittelflüssig
5-Minuten Epoxidharz

Carbon-Stäbe

Carbonstab 1 mm: 2 Stück (1000 mm Länge)
Carbonstab 1,5 mm: 5 Stück (1000 mm Länge)
Carbonstab 2 mm: 6 Stück (1000 mm Länge)

Stahldraht

Stahldraht 1 mm: 2 Stück (1000 mm Länge)

Magnete

Neodym-Magnet rund 8x2 mm (d x h): 1 Stück

Schrauben

Holzschrauben 2x10 mm (d x h): 26 Stück
Schraube M3x20 mm: 1 Stück
Schraube M3x30 mm: 1 Stück

Elektronik

Servos

Micro-Servos: 4 Stück (Maße maximal (L x B x H) 23.5 x 10 x 24 mm)
9g Mini-Servos können im Rumpf mit einer aktualisierten Servoplatte verwendet werden:
https://www.printables.com/de/model/204579-lukisegler-electric-rc-glider-update-servoplate-fo

Ich verwende hochwertige Servos mit Metallgetriebe. Diese stecken auch größere Belastungen (z.B. bei einem ungewünschten Bodenkontakt) ohne Schaden weg. Die Mehrkosten dafür lohnen sich.

Empfänger

Minimum: 5-Kanal

Motor

Brushless-Motor (Maße maximal (d x H) 28 x 50 mm)

ESC (Regler)

Minimum: 20A (3-4S)
BEC Minimum: 2A

Die komplette Bauanleitung gibt es auf meiner Website: https://c-arts-modelle.de/carts_modelle_web/fluggeraete/carts_lukisegler/carts_lukisegler.html

Meine Einstellungen in Prusaslicer:

Lukisegler (electric RC glider)

by c-arts-modelle · original on Printables ↗

Hobby & Makers / RC & Robotics

♥ 252⬇ 2.2k🖨 0 prints

License: Creative Commons — Attribution — Noncommercial — Share Alike ↗rcairplanercairplaneglidermodelairplanercgliderletadlomodellflugzeugflugzeug

Print profiles

22_l_QR_Segment_06_650-700mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
16_l_Segment_08_700-750mm_Vorderteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
08_r_Segment_04_300-400mm_Vorderteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
21_r_QR_Segment_05_600-650mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
03_l_Segment_02_100-200mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
23_l_QR_Segment_07_700-750mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
18_l_QR_Segment_02_450-500mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
24_r_Winglet_01_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
19_r_QR_Segment_03_500-550mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
11_l_Segment_06_500-600mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
27_Servohorn_klein_v04_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
02_r_Segment_01_0-100mm_Vorderteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
13_l_Segment_07_600-700mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
17_r_QR_Segment_01_400-450mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
15_r_Segment_08_700-750mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
22_r_QR_Segment_06_650-700mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
04_l_Segment_02_100-200mm_Vorderteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
28_opt_Gegenplatte_Servohorn_klein_v04_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
11_r_Segment_06_500-600mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
24_l_Winglet_01_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
06_r_Segment_03_200-300mm_Vorderteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
01_l_Segment_01_0-100mm_Hinterteil_v02_Ender3_PLALW.3mfDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
13_r_Segment_07_600-700mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
09_l_Segment_05_400-500mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
06_l_Segment_03_200-300mm_Vorderteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
16_r_Segment_08_700-750mm_Vorderteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
23_r_QR_Segment_07_700-750mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
21_l_QR_Segment_05_600-650mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
18_r_QR_Segment_02_450-500mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
14_r_Segment_07_600-700mm_Vorderteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
05_l_Segment_03_200-300mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
14_l_Segment_07_600-700mm_Vorderteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
02_l_Segment_01_0-100mm_Vorderteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
19_l_QR_Segment_03_500-550mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
15_l_Segment_08_700-750mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
25_l_Winglet_02_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
07_l_Segment_04_300-400mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
07_r_Segment_04_300-400mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
08_l_Segment_04_300-400mm_Vorderteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
09_r_Segment_05_400-500mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
03_r_Segment_02_100-200mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
01_r_Segment_01_0-100mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
17_l_QR_Segment_01_400-450mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
26_Servohalterung_Amewi_902MG_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
20_r_QR_Segment_04_550-600mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
04_r_Segment_02_100-200mm_Vorderteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
20_l_QR_Segment_04_550-600mm_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
25_r_Winglet_02_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
05_r_Segment_03_200-300mm_Hinterteil_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
05_Rumpfsegment_-180_-280_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
38_l_HR_Segment_1_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
08_Rumpfsegment_-480_-580_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
12_Befestigung_tragflaeche_hinten_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
15_Motorspant_v02_Ender3_PETG.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
35_l_HR_Stab_Segment_3_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
07_Rumpfsegment_-380_-480_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
40_r_HR_Segment_3_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
09_Rumpfsegment_-570_-660_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
04_Rumpfsegment_-080_-180_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
48_SR_Segment_1_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
35_r_HR_Stab_Segment_3_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
37_l_HR_Stab_Segment_5_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
34_r_HR_Stab_Segment_2_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
36_r_HR_Stab_Segment_4_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
11_Servoplatte_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
43_HR_Scharniere_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
37_r_HR_Stab_Segment_5_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
38_r_HR_Segment_1_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
24_Haube_hinten_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
53_SR_Stab_Segment_1a_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
50_SR_Segment_3_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
31_Kufe_hinten_02_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
40_l_HR_Segment_3_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
41_r_HR_Segment_4_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
22_Kufe_03_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
13_Befestigung_tragflaeche_vorne_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
26_Inlay_Haube_Gegenstueck_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
52_SR_Segment_5_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
58_Motorspant_vorne_opt_v02_Ender3_PETG.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
30_Kufe_hinten_01_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
25_Inlay_Haube_Magnet_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
33_l_HR_Stab_Segment_1_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
23_Haube_vorne_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
02_Rumpfsegment_120-020_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
39_r_HR_Segment_2_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
49_SR_Segment_2_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
10_Rumpfsegment_-660_-750_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
14_Haube_28x32_v02_Ender3_PETG.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
39_l_HR_Segment_2_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
41_l_HR_Segment_4_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
34_l_HR_Stab_Segment_2_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
33_r_HR_Stab_Segment_1_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
51_SR_Segment_4_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
29_r_Tragflaechenschraube_vorne_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
36_l_HR_Stab_Segment_4_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
21_Kufe_02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
32_Kufe_hinten_03_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
55_SR_Stab_Segment_2_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
06_Rumpfsegment_-280_-380_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
01_Rumpfsegment_220-120_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
42_r_HR_Segment_5_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
27_Haubenverschluss_vorne_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
57_SR_Stab_Segment_4_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
28_Tragflaechenschraube_hinten_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
56_SR_Stab_Segment_3_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
03_Rumpfsegment_020_-080_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
20_Kufe_01_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
54_SR_Stab_Segment_1b_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
29_l_Tragflaechenschraube_vorne_v02_Ender3_PLA.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
42_l_HR_Segment_5_v02_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
10_l_Segment_05_400-500mm_Vorderteil_v03_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
12_l_Segment_06_500-600mm_Vorderteil_v03_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
12_r_Segment_06_500-600mm_Vorderteil_v03_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
10_r_Segment_05_400-500mm_Vorderteil_v03_Ender3_PLALW.3mf
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print