The Flintstones are one of my favorite childhood cartoons.
Dino was modeled in Blender, sliced using Simplify3D and printed in ABS on a FlashForge Creator X.
If you have the proper filament colors, no painting is required.
The model is 24cm tall.
Enjoy, and I hope you have a "Yaba Daba Do" time printing this!
Note:
All parts were modeled from scratch except for the tongue. Dino's tongue was so close to Eddie's tongue (Thingiverse model 457259) that I saw no reason to improve on perfection. Credit for the tongue is duly noted.
3D PRINTING SETTINGS
Printer: FlashForge Creator X
Rafts: Yes
Supports: Yes
Resolution: .2mm
Infill: 10%
Notes:
Only a few pieces require some very minor supports and a raft. The majority of pieces do not require either. Refer to the notes below for details. I print all my models using 2 shells.
Colors
Black:
eyes
hair
spot1
spot2
spot3
spot4
spot5
Purple:
body
head
armr
arml
White:
eye_whites
tag
Beige/Pink/Skin (I used a light beige):
mouth
nose
Blue:
collar
Red:
tongue
Extra notes for printing
Pieces requiring minor supports around the low curves at the base:
armr, arml, mouth.
Pieces that may require a raft or brim (I use a brim):
tongue, head. I did not use a brim on the nose, but you may needed one.
Assembly
Assembly is fairly straight forward, refer to the following picture. I've listed a detailed step by step process below if guidance is needed.
*be sure to clean off any excess brim from the first layer if you use a "squish factor" for adhesion to the bed.
-Glue armr and arml to the body
-Insert and glue the spots as per the diagarm
-Hook the tag through the collar
-Insert and glue the collar to the body
-Glue the mouth to the head
-Glue the tongue to the mouth
-Glue the nose to the head, resting on the bridge of the mouth
-Insert the eye_whites, making a note of left and right (depressions for the eyes face toward the middle)
-Glue the eyes to the eye_whites. making a note of left and right eyes (there is a slight angle on each eye that should face towards the middle so that the eyes rest closer to the middle)
-Insert and glue the head into the collar.
-Glue the hair to the head. After careful trimming of any first layer brim, the hair should fit into the head.
Dino Flintstone
by reddadsteve · original on Printables ↗
World & Scans / Animals
♥ 322⬇ 1.2k🖨 45 prints
Print profiles
arml.stlDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
armr.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
eye_whites.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
mouth.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
eyes.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
body.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
spot1.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
spot2.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
collar.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
hair.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
spot3.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
nose.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
spot4.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
spot5.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
tag.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
head.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
tongue.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print