Speedloader for multiple types of magazines.
Print one body then the Insert type/types you need and switch out just the insert.
Easy Disassembly.
Springloaded.
Quick change insert/part replacement.
100% 3D Printed.
Thumb/Finger/Time/Sanity Saver!

Print instructions

Inserts Available for -

Glock/HK P2000 9mm, 40cal
Springfield XD
CZ 9mm
Springfield XDS
Taurus PT111, G2C
Walther Creed, PPX

Remix Insert by Jason N fits-

Sig P365
Springfield Hellcat (verified by FJBLBG)
SD9VE (verified by FJBLBG)

Remix Slide by William

Works better with Glock19x

All models provided have been tested. 40 cal or other magazines may work with the 9mm inserts like the Glock one does but I have none to test.

Recommend using PETG for durability, heat resistance if you're outside, and the springs springiness.

0.20 Layer thickness
All parts are pre-oriented for optimal printing

Total Body parts print time - 13 hours
Each Insert print time - 3 hours

Parts
Clips - 2 each - 25% infill
Lt and Rt body - 25% infill, support on build plate only

Stress parts
Slide - 100% infill
Inserts - 100% infill, support on build plate only
Springs - 2 each- 3 perimeters

Assembly
See pictures for reference

A light sanding and lubrication has been reported to work very well
Insert a spring into each body half
On one body half,
Place Insert wing into slot above spring
Place slide into slide groove in full forward/up position so the tail is resting on the lowest part of the Insert
Place other body half so insert wing is in slot above spring
Slide on front and rear clips
Reload to your hearts content

Haven't broken any parts yet but if they do its easy to replace

Troubleshooting

If the insert seems to stick and doesn't move smoothly or the insert doesn't seem to go down all the way and the round is not fully inserted into the magazine, there is probably too much overhang from the body binding on the springs,

Long fix - recalibrate your machine to do better bridge overhangs
Short fix - reprint springs, slice at 90-95% z-axis

SLV6 Magazine Speedloader

by Subtle3D · original on Printables ↗

Sports & Outdoor / Outdoor Sports

♥ 176⬇ 932🖨 18 prints

License: Creative Commons — Attribution — Noncommercial ↗creedgunglockhandgunpistolwaltherloader9mmreloaderspeedloadersigxdppxg2cpt111taurusspringfieldxdsp365hellcatsd9ve

Print profiles

sl-clip-v6.stlDEFAULT
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
sl-slide-v6.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
sl-spring-v6.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
sl-rt-body-v6.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
sl-insert-springfield-xds-9mm-v6.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
sl-lt-body-v6.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
sl-insert-taurus-pt111-g2c-9mm-v6.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
sl-insert-glock-40-9mm-v6.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
sl-insert-walther-creed-ppx-9mm-v6.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print
sl-insert-cz-xd-9mm-v6.stl
⏱ time and weight estimated after preparation · 1 material(s)
Made to order: we prepare this file when you order, which adds a few minutes before printing starts.
Prints on: A1 mini 0.4PLA
Order this print